1. # vim:set ft=sh
2. # MODULES
3. # The following modules are loaded before any boot hooks are
4. # run.  Advanced users may wish to specify all system modules
5. # in this array.  For instance:
6. #     MODULES=(usbhid xhci_hcd)
7. MODULES=(i915)
8.  
9. # BINARIES
10. # This setting includes any additional binaries a given user may
11. # wish into the CPIO image.  This is run last, so it may be used to
12. # override the actual binaries included by a given hook
13. # BINARIES are dependency parsed, so you may safely ignore libraries
14. BINARIES=()
15.  
16. # FILES
17. # This setting is similar to BINARIES above, however, files are added
18. # as-is and are not parsed in any way.  This is useful for config files.
19. FILES=()
20.  
21. # HOOKS
22. # This is the most important setting in this file.  The HOOKS control the
23. # modules and scripts added to the image, and what happens at boot time.
24. # Order is important, and it is recommended that you do not change the
25. # order in which HOOKS are added.  Run 'mkinitcpio -H <hook name>' for
26. # help on a given hook.
27. # 'base' is _required_ unless you know precisely what you are doing.
28. # 'udev' is _required_ in order to automatically load modules
29. # 'filesystems' is _required_ unless you specify your fs modules in MODULES
30. # Examples:
31. ##   This setup specifies all modules in the MODULES setting above.
32. ##   No RAID, lvm2, or encrypted root is needed.
33. #    HOOKS=(base)
34. #
35. ##   This setup will autodetect all modules for your system and should
36. ##   work as a sane default
37. #    HOOKS=(base udev autodetect modconf block filesystems fsck)
38. #
39. ##   This setup will generate a 'full' image which supports most systems.
40. ##   No autodetection is done.
41. #    HOOKS=(base udev modconf block filesystems fsck)
42. #
43. ##   This setup assembles a mdadm array with an encrypted root file system.
44. ##   Note: See 'mkinitcpio -H mdadm_udev' for more information on RAID devices.
45. #    HOOKS=(base udev modconf keyboard keymap consolefont block mdadm_udev encrypt filesystems fsck)
46. #
47. ##   This setup loads an lvm2 volume group.
48. #    HOOKS=(base udev modconf block lvm2 filesystems fsck)
49. #
50. ##   This will create a systemd based initramfs which loads an encrypted root filesystem.
51. #    HOOKS=(base systemd autodetect modconf kms keyboard sd-vconsole sd-encrypt block filesystems fsck)
52. #
53. ##   NOTE: If you have /usr on a separate partition, you MUST include the
54. #    usr and fsck hooks.
55. HOOKS=(base udev autodetect kms modconf block keyboard keymap consolefont plymouth filesystems fsck)
56.  
57. # COMPRESSION
58. # Use this to compress the initramfs image. By default, zstd compression
59. # is used for Linux ≥ 5.9 and gzip compression is used for Linux < 5.9.
60. # Use 'cat' to create an uncompressed image.
61. #COMPRESSION="zstd"
62. #COMPRESSION="gzip"
63. #COMPRESSION="bzip2"
64. #COMPRESSION="lzma"
65. #COMPRESSION="xz"
66. #COMPRESSION="lzop"
67. #COMPRESSION="lz4"
68.  
69. # COMPRESSION_OPTIONS
70. # Additional options for the compressor
71. #COMPRESSION_OPTIONS=()
72.  
73. # MODULES_DECOMPRESS
74. # Decompress loadable kernel modules and their firmware during initramfs
75. # creation. Switch (yes/no).
76. # Enable to allow further decreasing image size when using high compression
77. # (e.g. xz -9e or zstd --long --ultra -22) at the expense of increased RAM usage
78. # at early boot.
79. # Note that any compressed files will be placed in the uncompressed early CPIO
80. # to avoid double compression.
81. #MODULES_DECOMPRESS="no"
82.